parameter symbol unit conditions ratings absolute maximum ratings electrical characteristics parameter symbol min typ max unit conditions ratings (ta=25?) power supply voltage input terminal voltage input terminal current dg terminal voltage input voltage inpup current operating power supply voltage quiescent circuit current thermal shutdown operating temperature load open detection threshold voltage dg leak current low level dg output voltage output transfer time dg output transfer time (v b = 14v, ta=25? unless otherwise specified) output on resistance channel temperature operating temperature storage temperature v b v in i in v b (opr) v in = 0v, v out =0v i o =2a i o =1 a, ta=80? v in =5v v out =v o 1.5v v out =0v v dg = 5.5v i dg = 1.6ma v 50 2.0 1.8 70 1 5.5 35 ma 150 m ? 250 m ? 3.0 v v a 165 10 165 3 60 0.15 70 45 20 155 ? a v s s a v s iq output leak current v out =0v ta= ?0 to +105? ta= ?0 to +105? 1.0 a i o , leak r ds (on) v ih v il i ih t tsd overcurrent protection starting current internal current limit 2.6 a i s i lim vopen t on t off v dgl i dg t plh t phl s v dg v ds i o p d i f tch t op tstg output on output off output on v v ta=25? ma v v a w a ? ? ? 35 ?.3 to 7 5 ?.3 to 7 dg terminal current drain to source voltage output current power dissipation source to drain di forward current i dg ma 5 v b ?5 2.5 2.7 0.8 150 ?0 to +105 ?0 to +150 parameter unit ratings recommended operating conditions (for one channel) power supply voltage v ih v il i o r in r dg 5.5 4 ?.3 10 10 16 5.5 0.9 1.15 20 20 v v v a k ? k ? external dimensions (unit: mm) features built-in diagnostic function to detect short and open circuiting of loads and output status signals dmos 2ch output allows on/off using c-mos logic level built-in overcurrent and thermal protection circuits 42 high-side power switch ics [with diagnostic function, surface-mount 2-circuits] spf5004 min max block diagram (for one channel) standard connection diagram timing chart in dg v b gnd out thermal protect input logic lavel shifting dg logic open/short sense charge pump current limit clamp chopper bias vin 1 (7v max) vin 2 (7v max) gnd dg2 dg1 5v out1 out2 5v (16,17,18) 13 23 c p u 9 21 24 12 14,15 2,3 11 1 spf5004 v b (4,5,6) 1.0 10.5 0.3 +0.1 0.05 0.25 +0.15 0.05 2.0 +0.2 0.8 fin thickness 17.28 0.2 2.5 0.2 7.5 0.2 15.58 0.2 1.27 0.25 24 112 13 0.4 +0.15 0.05 a b a: part no. b: lot no. * make v b of 4pin, 5pin, 6pin, 16pin, 17pin and 18pin short from the fin to be plated by solder. r in r in r dg r dg load load v b v in on v in off v o open ocp tsd normal normal over- heat normal normal normal shorted load open load high inpidance internal current limit tsd on tsd off v in v out i out dg v in dg open load normal mode shorted load overheat h l v o h l h l h l h h h h h l l l l l (limiting) h l l l l l
|
